dip switches grayhill, inc. ? 561 hillgrove avenue ? lagrange, illinois 60525-5997 ? usa ? phone: 708-354-1040 ? fax: 708-354-2820 ? www.gra yhill.com series 79b linear action, coded output features reliable switching, positive detent codes in bcd and hexadecimal true zero output 10 or 16 positions 2000 cycle life up to 60,000 detent operations dimensions in inches (and millimeters) circuitry specifications electrical ratings make-and-break current rating: 2,000 cycles at 10 ma, 50 mvdc; 2,000 cycles at 125 ma, 6 vdc; 2,000 cycles at 50 ma, 30 vdc. contact resistance: 100 mohms maximum after life, measured at 10 ma dc and 50 mv (open circuit). initial values are 60 mohms maximum for coded switches, and 50 mohms for other linear action switches. insulation resistance (at 100 vdc): between adjacent isolated contacts: initial: 5,000 mohms minimum; after life: 1,000 mohms minimum across open contacts: initial: 5,000 mohms minimum; after life: 1,000 mohms minimum dielectric strength: between adjacent isolated contacts and across open contacts. initial: 750 vac; after life: 500 vac contact carry rating: 2 amps with a maximum contact temperature rise of 20c. mechanical ratings mechanical life: 4,000 cycles maximum. note: a cycle is one complete operation, back and forth through all switch positions. vibration resistance: 10 to 2,000 hz at 15g or 0.060" double amplitude; no damage and no contact openings exceeding 10 ms (method 204, test condition b). shock resistance: 509, 11 ms, half sine; no damage and no openings exceeding 10 microseconds (method 213, test condition a). environmental ratings refer to mil-std-202f per mil-s-83504 operating temperature range: -40c to +85c storage temperature range: -55c to +85c moisture resistance: 240 hours with temperature cycling and polarization, per mil- std-202f, method 305 materials and finishes nonconductive parts: plastic ul94v-o shorting arm: phosphor bronze, gold plate over nickel plate base contacts: copper alloy, gold plate over nickel plate terminals: copper alloy, matte tin plated over nickel barrier potting material: epoxy tape seal and packaging tape seal: polyester film *a top tape seal is required for switches that are machine soldered or heavily cleaned after hand soldering. to order top seal versions, add "s" before the "t" in the grayhill part number. available from your local grayhill distributor. for prices and discounts, contact a local sales office, an authorized local distributor or grayhill. all dimensions not shown here are the same as those on the facing page. 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 a b c d e f 0 1 2 4 8 0 1 2 4 8 .100 .005 (2,54 0,13) typ. c l c l c l c l .240 .005 (6.10 0,13) typ. .100 .005 (2,54 0,13) typ. .390 .005 (9,91 0,13) .490 .005 (12,45 0,13) .100 .005 (2,54 0,13) typ. c l c l .100 .005 (2,54 0,13) typ. c l c l see note a see note a note a: all terminals on this side of the switch are bussed internally. any one of them may be used as the common terminal. switch positions 0 1 2 3 4 5 6 7 8 9 a b c d e f 16 10 012480 1248 binary codes terminal locations dot indicates contact made between contact and output terminal. number of positions type of circuit code number per tube part number* 10 binary code decimal 9 79b10t 16 hexadecimal 6 79B16T ordering information dip 16 thru-hole dip switches
|
